Documentation Center |
The ACPR System object™ measures adjacent channel power ratio (ACPR) of an input signal.
To measure adjacent channel power:
Define and set up your adjacent channel power object. See Construction.
Call step to measure the adjacent channel power ratio according to the properties of comm.ACPR. The behavior of step is specific to each object in the toolbox.
H = comm.ACPR creates a System object, H, that measures adjacent channel power ratio (ACPR) of an input signal.
H = comm.ACPR(Name,Value) creates object, H, with each specified property set to the specified value. You can specify additional name-value pair arguments in any order as (Name1,Value1,...,NameN,ValueN).
NormalizedFrequency |
Assume normalized frequency values Specify whether the frequency values are normalized. If you set this property to true, the object assumes that frequency values are normalized (in the [-1 1] range). The default is false. If you set this property to false, the object assumes that frequency values are measured in Hertz. |
SampleRate |
Sample rate of input signal Specify the sample rate of the input signal, in samples per second, as a double-precision, positive scalar. The default is 1e6 samples per second. This property applies when you set the NormalizedFrequency property to false. |
MainChannelFrequency |
Main channel center frequency Specify the main channel center frequency as a double-precision scalar. The default is 0 Hz. When you set the NormalizedFrequency property to true, you must specify the center frequency as a normalized value between -1 and 1. When you set the NormalizedFrequency property to false, you must specify the center frequency in Hertz. The object measures the main channel power in the bandwidth that you specify in the MainMeasurementBandwidth property. This measurement is taken at the center of the frequency that you specify in the MainMeasurementBandwidth property. |
MainMeasurementBandwidth |
Main channel measurement bandwidth Specify the main channel measurement bandwidth as a double-precision, positive scalar. The default is 50e3 Hz. When you set the NormalizedFrequency property to true, you must specify the measurement bandwidth as a normalized value between 0 and 1. When you set the NormalizedFrequency property to false, you must specify the measurement bandwidth in Hertz. The object measures the main channel power in the bandwidth that you specify in the MainMeasurementBandwidth property. This measurement is taken at the center of the frequency that you specify in the MainChannelFrequency property. |
AdjacentChannelOffset |
Adjacent channel frequency offsets Specify the adjacent channel offsets as a double-precision scalar or as a row vector comprising frequencies that define the location of adjacent channels of interest. The default is [-100e3 100e3] Hz. When you set the NormalizedFrequency property to true, you must specify normalized frequency offset values between -1 and 1. When you set the NormalizedFrequency property to false, you must specify frequency offset values in Hertz. The offset values indicate the distance between the main channel center frequency and adjacent channel center frequencies. Positive offsets indicate adjacent channels to the right of the main channel center frequency. Negative offsets indicate adjacent channels to the left of the main channel center frequency. |
AdjacentMeasurementBandwidth |
Adjacent channel measurement bandwidths Specify the measurement bandwidth for each adjacent channel. The default is the scalar, 50e3. The object assumes that each adjacent bandwidth is centered at the frequency defined by the corresponding frequency offset. You define this offset in the AdjacentChannelOffset property. Set this property to a double-precision scalar or row vector of length equal to the number of specified offsets in the AdjacentChannelOffset property. When you set this property to a scalar, the object obtains all adjacent channel power measurements within equal measurement bandwidths. When you set the NormalizedFrequency property to true, you must specify normalized bandwidth values between 0 and 1. When you set the NormalizedFrequency property to false, you must specify the adjacent channel bandwidth values in Hertz. |
MeasurementFilterSource |
Source of the measurement filter Specify the measurement filter source as one of None | Property. The default is None. When you set this property to None the object does not apply filtering to obtain ACPR measurements. When you set this property to Property, the object applies a measurement filter to the main channel before measuring the average power. Each of the adjacent channel bands also receives a measurement filter . In this case, you specify the measurement filter coefficients in the MeasurementFilter property. |
MeasurementFilter |
Measurement filter coefficients Specify the measurement filter coefficients as a double-precision row vector containing the coefficients of an FIR filter in descending order of powers of z. Center the response of the filter at DC. The ACPR object automatically shifts and applies the filter response at each of the main and adjacent channel center frequencies before obtaining the average power measurements. The internal filter states persist and clear only when you call the reset method. This property applies when you set the MeasurementFilter property to Property. The default is 1, which is an all-pass filter that has no effect on the measurements. |
SpectralEstimation |
Spectral estimation control Specify the spectral estimation control as one of Auto | Specify frequency resolution | Specify window parameters. The default is Auto. When you set this property to Auto, the object obtains power measurements with a Welch spectral estimator with zero-percent overlap, a Hamming window, and a segment length equal to the length of the input data vector. In this setting, the spectral estimator set should achieve the maximum frequency resolution attainable with the input data length. When you set this property to Specify frequency resolution, you specify the desired spectral frequency resolution, in normalized units or in Hertz, using the FrequencyResolution property. In this setting, the object uses the value in the FrequencyResolution property to automatically compute the size of the spectral estimator data window. When you set this property to Specify window parameters, several spectral estimator properties become available so that you can control the Welch spectral estimation settings. These properties are: SegmentLength, OverlapPercentage, Window, and SidelobeAttenuation. Sidelobe attenuation applies only when you set the Window property to Chebyshev. When you set the this property to Specify window parameters, the FrequencyResolution property does not apply, and you control the resolution using the above properties. |
SegmentLength |
Segment length Specify the segment length, in samples, for the spectral estimator as a numeric, positive, integer scalar. The default is 64. The length of the segment allows you to make tradeoffs between frequency resolution and variance in the spectral estimates. A long segment length results in better resolution. A short segment length results in more averaging and a decrease in variance. This property applies when you set the SpectralEstimation property to Specify window parameters. |
OverlapPercentage |
Overlap percentage Specify the percentage of overlap between each segment in the spectral estimator as a double-precision scalar in the [0 100] interval. This property applies when you set the SpectralEstimation property to Specify window parameters. The default is 0 percent. |
Window |
Window function Specify a window function for the spectral estimator as one of Bartlett | Bartlett-Hanning | Blackman | Blackman-Harris | Bohman | Chebyshev | Flat Top | Hamming | Hann | Nuttall | Parzen | Rectangular | Triangular. The default is Hamming. A Hamming window has 42.5dB of sidelobe attenuation. This attenuation may mask spectral content below this value, relative to the peak spectral content. Choosing different windows allows you to make tradeoffs between resolution and sidelobe attenuation. This property applies when you set the SpectralEstimation property to Specify window parameters. |
SidelobeAttenuation |
Sidelobe attenuation for Chebyshev window Specify the sidelobe attenuation, in decibels, for the Chebyshev window function as a double-precision, nonnegative scalar. The default is 100 dB. This property applies when you set the SpectralEstimation property to Specify window parameters and the Window property to Chebyshev. |
FrequencyResolution |
Frequency resolution Specify the frequency resolution of the spectral estimator as a double-precision scalar. The default is 10625 Hz. When you set the NormalizedFrequency property to true, you must specify the frequency resolution as a normalized value between 0 and 1. When you set the NormalizedFrequency property to false, you must specify the frequency resolution in Hertz. The object uses the value in the FrequencyResolution property to calculate the size of the data window used by the spectral estimator. This property applies when you set the SpectralEstimation property to Specify frequency resolution. |
FFTLength |
FFT length Specify the FFT length that the Welch spectral estimator uses as one of Next power of 2 | Same as segment length | Custom. The default is Next power of 2. When you set this property to Custom, the CustomFFTLength property becomes available to specify the desired FFT length. When you set this property to Next power of 2, the object sets the length of the FFT to the next power of 2. This length is greater than the spectral estimator segment length or 256, whichever is greater. When you set this property to Same as segment length, the object sets the length of the FFT. This length equals the spectral estimator segment length or 256, whichever is greater. |
CustomFFTLength |
Custom FFT length Specify the number of FFT points that the spectral estimator uses as a numeric, positive, integer scalar. This property applies when you set the FFTLength property to Custom. The default is 256. |
MaxHold |
Max-hold setting control Specify the maximum hold setting. The default is false. When you set this property to true, the object compares two vectors. One vector compared is the current estimated power spectral density vector (obtained with the current input data frame). The object checks this vector against the previous maximum-hold accumulated power spectral density vector, (obtained at the previous call to the step method). The object stores the maximum values at each frequency bin and uses them to compute average power measurements. You clear the maximum-hold spectrum by calling the reset method on the object. When you set this property to false, the object obtains power measurements using instantaneous power spectral density estimates. This property is tunable. |
PowerUnits |
Power units Specify power measurement units as one of dBm | dBW | Watts. The default is dBm. When you set this property to dBm, or dBW, the step method outputs ACPR measurements in a dBc scale (adjacent channel power referenced to main channels power). If you set this property to Watts, the step method outputs ACPR measurements in a linear scale. |
MainChannelPowerOutputPort |
Enable main channel power measurement output When you set this property to true, the step method outputs the main channel power measurement. The default is false. The main channel power is the power of the input signal measured in the band that you define with the MainChannelFrequency and MainMeasurementBandwidth properties. The step method returns power measurements in the units that you specify in the PowerUnits property. |
AdjacentChannelPowerOutputPort |
Enable adjacent channel power measurements output When you set this property to true, the step method outputs a vector of adjacent channel power measurements. The default is false. The adjacent channel powers correspond to the input signal's power measured in the bands that you define with the AdjacentChannelOffset and AdjacentMeasurementBandwidth properties. The step method returns power measurements in the units that you specify in the PowerUnits property. |
clone | Create ACPR measurement object with same property values |
getNumInputs | Number of expected inputs to step method |
getNumOutputs | Number of outputs from step method |
isLocked | Locked status for input attributes and nontunable properties |
release | Allow property value and input characteristics changes |
reset | Reset states of ACPR measurement object |
step | Adjacent Channel Power Ratio measurements |