Write audio file
audiowrite(filename,y,Fs) writes a matrix of audio data, y, with sample rate Fs to a file called filename. The filename input also specifies the output file format. The output data type depends on the output file format and the data type of the audio data, y.
Create a WAVE file from the example file handel.mat, and read the file back into MATLAB®.
Write a WAVE (.wav) file in the current folder.
load handel.mat filename = 'handel.wav'; audiowrite(filename,y,Fs); clear y Fs
Read the data back into MATLAB using audioread.
[y,Fs] = audioread(filename);
Listen to the audio.
Create a FLAC file from the example file handel.mat and specify the number of output bits per sample and a comment.
load handel.mat filename = 'handel.flac'; audiowrite(filename,y,Fs,'BitsPerSample',24,'Comment','This is my new audio file.'); clear y Fs
View information about the new FLAC file.
info = audioinfo(filename)
info = Filename: 'S:\handel.flac' CompressionMethod: 'FLAC' NumChannels: 1 SampleRate: 8192 TotalSamples: 73113 Duration: 8.9249 Title:  Comment: 'This is my new audio file.' Artist:  BitsPerSample: 24
Name of file to write, or the full path to the file, specified as a string that includes the file extension. If a path is specified, it can be absolute or relative. If you do not specify the path, then the destination directory is the current working directory.
audiowrite supports the following file formats.
|Platform Support||File Format|
|All platforms||WAVE (.wav)|
|Windows® and Mac||MPEG-4 AAC (.m4a, .mp4)|
When writing AAC files on Windows, audiowrite pads the front and back of the output signal with extra samples of silence. The Windows AAC encoder also places a very sharp fade-in and fade-out on the audio. This results in audio with an increased number of samples after being written to disk.
Audio data to write, specified as an m-by-n matrix, where m is the number of audio samples to write and n is the number of audio channels to write.
If either m or n is 1, then audiowrite assumes that this dimension specifies the number of audio channels, and the other dimension specifies the number of audio samples.
The maximum number of channels depends on the file format.
|File Format||Maximum Number of Channels|
|MPEG-4 AAC (.m4a, .mp4)||2|
The valid range for the data in y depends on the data type of y.
|Data Type of y||Valid Range for y|
|uint8||0 ≤ y ≤ 255|
|int16||-32768 ≤ y ≤ +32767|
|int32||-2^32 ≤ y ≤ 2^32–1|
|single||-1.0 ≤ y ≤ +1.0|
|double||-1.0 ≤ y ≤ +1.0|
Data beyond the valid range is clipped.
If y is single or double, then audio data in y should be normalized to values in the range −1.0 and 1.0, inclusive.
Data Types: single | double | int16 | int32 | uint8
Sample rate, in hertz, of audio data y, specified as a positive scalar greater than 0. Values of Fs are truncated to integer boundaries. When writing to .m4a or .mp4 files on Windows platforms, audiowrite supports only samples rates of 44100 and 48000.
Data Types: double
Specify optional comma-separated pairs of Name,Value arguments. Name is the argument name and Value is the corresponding value. Name must appear inside single quotes (' '). You can specify several name and value pair arguments in any order as Name1,Value1,...,NameN,ValueN.Example: 'Title','Symphony No. 9','Artist','My Orchestra' instructs audiowrite to write an audio file with the title "Symphony No. 9" and the artist information "My Orchestra."
Number of output bits per sample, specified as the comma-separated pair consisting of 'BitsPerSample' and a number.
Only available for WAVE (.wav) and FLAC (.flac) files. For FLAC files, only 8, 16, or 24 bits per sample are supported.
Number of kilobits per second (kbit/s) used for compressed audio files, specified as the comma-separated pair consisting of 'BitRate' and an integer. Noninteger values are truncated. On Windows 7 platforms, the only valid values are 96, 128, 160, and 192.
In general, a larger BitRate value results in higher compression quality.
Only available for MPEG-4 (.m4a, .mp4) files.
Quality setting for the Ogg Vorbis Compressor, specified as the comma-separated pair consisting of 'Quality' and a number in the range [0 100], where 0 is lower quality and higher compression, and 100 is higher quality and lower compression.
Only available for OGG (.ogg) files.
Title information, specified as the comma-separated pair consisting of 'Title' and a string.
Artist information, specified as the comma-separated pair consisting of 'Artist' and a string.
Additional information, specified as the comma-separated pair consisting of 'Comment' and a string.
|File Formats||Data Type of y||Output BitsPerSample||Output Data Type|
|WAVE (.wav),||uint8, int16, int32, single, double||8||uint8|
|uint8, int16, int32||32||int32|
|FLAC (.flac)||uint8, int16, int32, single, double||8||int8|
|MPEG-4 (.m4a, .mp4),|
|uint8, int16, int32, single, double||N/A||single|