|On this page…|
Sometimes your objective function or nonlinear constraint function values are available only by simulation or by numerical solution of an ordinary differential equation (ODE). Such optimization problems have several common characteristics and challenges, discussed in Potential Problems and Solutions.
To optimize a Simulink® model easily, try using Simulink Design Optimization™.
Optimization Toolbox™ solvers use derivatives of objective and constraint functions internally. By default, they estimate these derivatives using finite difference approximations of the form
These finite difference approximations can be inaccurate because:
A large value of δ allows more nonlinearity to affect the finite difference.
A small value of δ leads to inaccuracy due to limited precision in numerics.
Specifically, for simulations and numerical solutions of ODEs:
Simulations are often insensitive to small changes in parameters. This means that if you use too small a perturbation δ, the simulation can return a spurious estimated derivative of 0.
Both simulations and numerical solutions of ODEs can have inaccuracies in their function evaluations. These inaccuracies can be amplified in finite difference approximations.
Numerical solution of ODEs introduces noise at values much larger than machine precision. This noise can be amplified in finite difference approximations.
If an ODE solver uses variable step sizes, then sometimes the number of ODE steps in the evaluation of F(x + δ) can differ from the number of steps in the evaluation of F(x). This difference can lead to a spurious difference in the returned values, giving a misleading estimate of the derivative.
Avoid Finite Differences by Using Direct Search. If you have a Global Optimization Toolbox license, you can try using patternsearch as your solver. patternsearch does not attempt to estimate gradients, so does not suffer from the limitations in Problems in Finite Differences.
If you use patternsearch for expensive (time-consuming) function evaluations, use the Cache option:
options = psoptimset('Cache','on');
If you cannot use patternsearch, and have a relatively low-dimensional unconstrained minimization problem, try fminsearch instead. fminsearch does not use finite differences. However, fminsearch is not a fast or tunable solver.
Set Larger Finite Differences. You can sometimes avoid the problems in Problems in Finite Differences by taking larger finite difference steps than the default.
If you have MATLAB® R2011b or later, set the FinDiffRelStep option to a value larger than the default sqrt(eps) or eps^(1/3), such as:
options = optimset('FinDiffRelStep',1e-3);
For R2013a onwards:
options = optimoptions('solvername','FinDiffRelStep',1e-3);
If you have different scales in different components, set FinDiffRelStep to a vector proportional to the component scales.
If you have MATLAB R2011a or earlier, set the DiffMinChange option to a larger value than the default 1e-8, and possibly set the DiffMaxChange option also, such as:
options = optimset('DiffMinChange',1e-3,'DiffMaxChange',1);
You can also try setting central finite differences:
options = optimoptions('solvername','FinDiffType','central');
Use a Gradient Evaluation Function. To avoid the problems of finite difference estimation, you can give an approximate gradient function in your objective and nonlinear constraints. Remember to set the GradObj option to 'on' using optimoptions, and, if relevant, also set the GradConstr option to 'on'.
For some ODEs, you can evaluate the gradient numerically at the same time as you solve the ODE. For example, suppose the differential equation for your objective function z(t,x) is
where x is the vector of parameters over which you minimize. Suppose x is a scalar. Then the differential equation for its derivative y,
where z(t,x) is the solution of the objective function ODE. You can solve for y(t,x) in the same system of differential equations as z(t,x). This solution gives you an approximated derivative without ever taking finite differences. For nonscalar x, solve one ODE per component.
For some simulations, you can estimate a derivative within the simulation. For example, the likelihood ratio technique described in Reiman and Weiss  or the infinitesimal perturbation analysis technique analyzed in Heidelberger, Cao, Zazanis, and Suri  estimate derivatives in the same simulation that estimates the objective or constraint functions.
Use Tighter ODE Tolerances. You can use odeset to set the AbsTol or RelTol ODE solver tolerances to values below their defaults. However, choosing too small a tolerance can lead to slow solutions, convergence failure, or other problems. Never choose a tolerance less than 1e-9 for RelTol. The lower limit on each component of AbsTol depends on the scale of your problem, so there is no advice.
If a simulation uses random numbers, then evaluating an objective or constraint function twice can return different results. This affects both function estimation and finite difference estimation. The value of a finite difference might be dominated by the variation due to randomness, rather than the variation due to different evaluation points x and x + δ.
If your simulation uses random numbers from a stream you control, reset the random stream before each evaluation of your objective or constraint functions. This practice can reduce the variability in results. For example, in an objective function:
function f = mysimulation(x) rng('default') % or any other resetting method ... end
For details, see Generate Random Numbers That Are Repeatable.
Frequently, a simulation evaluates both the objective function and constraints during the same simulation run. Or, both objective and nonlinear constraint functions use the same expensive computation. Solvers such as fmincon separately evaluate the objective function and nonlinear constraint functions. This can lead to a great loss of efficiency, because the solver calls the expensive computation twice. To circumvent this problem, use the technique in Objective and Nonlinear Constraints in the Same Function.
Your simulation or ODE can fail for some parameter values.
Set Appropriate Bounds. While you might not know all limitations on the parameter space, try to set appropriate bounds on all parameters, both upper and lower. This can speed up your optimization, and can help the solver avoid problematic parameter values.
Use a Solver That Respects Bounds. As described in Iterations Can Violate Constraints, some algorithms can violate bound constraints at intermediate iterations. For optimizing simulations and ODEs, use algorithms that always obey bound constraints. See Algorithms That Satisfy Bound Constraints.
Return NaN. If your simulation or ODE solver does not successfully evaluate an objective or nonlinear constraint function at a point x, have your function return NaN. Most Optimization Toolbox and Global Optimization Toolbox solvers have the robustness to attempt a different iterative step if they encounter a NaN value. These robust solvers include:
fmincon interior-point, sqp, and trust-region-reflective algorithms
Some people are tempted to return an arbitrary large objective function value at an unsuccessful, infeasible, or other poor point. However, this practice can confuse a solver, because the solver does not realize that the returned value is arbitrary. When you return NaN, the solver can attempt to evaluate at a different point.
 Heidelberger, P., X.-R. Cao, M. A. Zazanis, and R. Suri. Convergence properties of infinitesimal perturbation analysis estimates. Management Science 34, No. 11, pp. 1281–1302, 1988.
 Leis, J. R., and Kramer, M.A. The Simultaneous Solution and Sensitivity Analysis of Systems Described by Ordinary Differential Equations. ACM Trans. Mathematical Software, Vol. 14, No. 1, pp. 45–60, 1988.
 Raue, A., et al. Lessons Learned from Quantitative Dynamical Modeling in Systems Biology. Available at http://www.plosone.org/article/info:doi/10.1371/journal.pone.0074335, 2013.
 Reiman, M. I., and A. Weiss. Sensitivity analysis via likelihood ratios. Proc. 18th Winter Simulation Conference, ACM, New York, pp. 285–289, 1986.